Bootloader/Firmware Testing and Recovery

LAVA supports deploying new bootloader/firmware builds with recovery from broken builds on boards which meet full bootloader automation criteria. When using LAVA as a part of Continuous Integration, it is expected that some of the bootloader builds will fail due to new bugs or regressions, just as with any other software being tested.

Note

For the purposes of this documentation, LAVA does not make any distinction between firmware and bootloader on the boards that it supports. Support depends simply on the ability to recover the board after a deployment of a broken build.

A reliable, effective and low-operational-cost automation methodology requires automated recovery without any manual intervention. [1] In an environment where there is a mixed user pool, a board needs to be available for the next test job in the queue, using a known working bootloader build, as soon as the recovery from the previous test job is complete.

Recovery should be a conditional element of every bootloader test job using a second deploy and boot action. LAVA has support for fixing up a broken bootloader build by running a health check test job to deploy a known working build, as long as the breakage can be reliably detected. The bootloader deployment and recovery test job should raise an infrastructure error to automatically trigger a health check.

Bootloader testing on boards which do not provide for automated recovery cannot be supported by automation.

[1]A smaller number of boards support automated installation of a bootloader but don’t support automated recovery. In an environment where failures are expected, introducing manual recovery steps in an otherwise automated testing environment should be considered very carefully.

What is recovery mode?

Recovery mode is a hardware feature which allows boards to be unbricked after a serious system error or a failed update of the bootloader, kernel or operating system. Recovery mode is not necessarily the same as the methods used to deploy firmware to a bare metal device during manufacture.

  • Recovery mode needs to implement a way to write a new bootloader build which must be fully usable even if the bootloader is absent or invalid, i.e. without any attempt to execute the current bootloader.
  • Recovery mode must be able to write a new bootloader to the board directly after applying power to the device and then allow the board to execute the new bootloader to continue operation upon leaving recovery mode.

Bootloader recovery criteria

Juno, HiKey 6220 and X15 GPEVM are the only boards capable of supporting bootloader testing and recovery out of the hundreds of boards which have been integrated into LAVA over the years.

Note

Of the supported boards, the HiKey 6220 has noticeable limitations. It is possible to workaround some difficulties on some boards but this will limit the usefulness and scope of any bootloader testing on those boards.

The difficulties cover a number of areas:

Reliability

All aspects of bootloader testing and recovery need to be reliable for CI to operate:

  • Entering and leaving recovery mode
  • Appearance of interfaces to transfer data within recovery mode
  • Transfer of data during recovery
  • Stability of the hardware during recovery (considering that the files being transferred - and executed - are untested, may contain invalid sequences or be corrupted during the build).

Uniqueness

Automation relies on being able to identify one board out of hundreds, some of which will be in the same or very similar states to the one board in use for this test job.

  • Every board needs to expose a distinct identifier across all interfaces.

    Important

    The HiKey 6220 cannot do this in recovery mode and is therefore restricted to only one board for each worker. This dramatically reduces the availability of bootloader testing and recovery using this board.

  • All identifiers must be independent of the software deployed on the device. If identifiers change when firmware is updated, the board will effectively disappear underneath the automation.

  • All identifiers must be stable across reboots and test jobs.

Scalability

Keep Things Simple. Every item below adds to the complexity of the final test jobs and failure rates will rise, in a non-linear manner, with each increase in complexity.

  • Jumpers require relays which require software control interfaces

  • Relays will eventually fail after a finite number of operations.

  • Recovery mode devices which appear or disappear after a hardware timeout will be a cause of intermittent failures.

  • Hardware modifications cause deviations from the original or final product, potentially invalidating some results.

  • Not all automation admin teams have the necessary hardware experience to make modifications to a board.

  • Custom hardware peripherals can interfere with board hardware or software causing intermittent failures or non-standard behavior.

  • Security requirements of a production / consumer device are typically incompatible with automation requirements. Access to recovery mode may be removed to prevent consumer access to protected content. Nonetheless, try to get as much of the recovery mode support available out-of-the-box as possible to manage the failure rate.

  • The further the automation infrastructure diverges from the manufacturer infrastructure, the harder it will be to triage and fix the problems with the bootloader. This is a particular problem for intermittent failures.

    If the manufacturer has a custom rig used to deploy the original firmware, a copy of such a rig may be a significant advantage when automating bootloader testing and recovery. The lack of such a rig has blocked bootloader testing and recovery on several boards.

Deployment

Automation must always be able to interrupt the boot process at a stage lower than the stage being tested. This is why a BMC is so useful, provided that the operation of the BMC is stable, reliable and deterministic.

Comparison of barriers to bootloader testing and recovery

LAVA has a low tolerance for failure so that issues can be detected early, avoiding a false positive where a test passes because an error was not detected. Developers will need reliable result data from the automated bootloader testing and recovery to avoid wasting time on spurious false negative reports which mis-report a failure as being caused by the code when it was due to the automation infrastructure. The hardest problems to solve are intermittent faults in a complex stack Every requirement which is not fully supported adds complexity to the final automation and risks increasing the failure rate.

Requirement HiKey 6220 BL Juno X15 GPEVM BL
Interrupt boot before bootloader [2] Yes Yes Yes
Presence of a recovery mode [3] Yes Yes Yes
Automated access to recovery [4] Needs relays Yes Needs relays
Writing data in recovery mode [5] Dynamic USB TTY Yes Dynamic USB TTY
Unique identification in recovery [6] NO Yes Yes
Stable operation in recovery Yes Yes Yes
[2]See Deployment - most boards in LAVA cannot provide this support.
[3]See What is recovery mode?
[4]

Consumer devices need to be protected from accidentally entering recovery mode, so manufacturers put constraints on how recovery mode is accessed. For example, having to press multiple buttons at the same time or in a specific order or hold down until something shows on the screen. For recovery mode to be used in automation, access to recovery mode must be as simple as possible - complexity always increases the failure rate.

HiKey 6220 and X15 GPEVM have jumpers to select recovery mode which is easier to automate than buttons but still requires external hardware which then needs additional software to be written to automate the control of the board. Attaching relays to jumpers is very different to soldering connections onto a DIP switch. Many lab admin teams do not include a hardware engineer.

[5]The use of dynamic devices like /dev/ttyUSB* requires unique identification in recovery mode.
[6]The HiKey 6220 dynamic USB TTY device does not have a unique identifier on the host. If board-01 is already in recovery mode and board-02 enters recovery mode whilst connected to the same host, board-01 becomes inaccessible. This limits the use of recovery mode to one board per host.

Defensive testing

Avoid creating a burden on all boards to support bootloader testing and recovery from only some test jobs. Once intermittent errors occur with boards which need some level of custom support for recovery mode, it will be much harder to investigate if the failure cannot be tested on boards which do not have recovery mode support. It would be better to have two device types, one with recovery mode support and one without, whenever there is any doubt about the reliability of the recovery mode support.

Problems with bootloader execution

Some boards can support replacing the bootloader within a test job but still rely on the current bootloader to execute to allow the board to boot to a stage where that functionality is available. For example, it is possible to write new U-Boot files to many U-Boot devices once booted into a ramdisk from within a test job. Alternatively, fastboot devices support writing a new fastboot binary at the same stage as writing a new kernel or system image. This does not qualify as recovery mode because those same files must be executed before the board can boot to the stage where new files can be written.

Two serious failures are possible:

  • the new files fail to execute in the ways required by the automation, requiring manual intervention
  • the new files contain a failure not executed by the automation, potentially requiring a product recall

Therefore, the bootloader files must undergo manual testing before being made available and this dramatically limits the opportunity for CI on those bootloader files.

For example, fastboot mode is not recovery mode for two reasons:

  • the fastboot binary can be overwritten (by fastboot) within normal operation of a test job and therefore rendered corrupt or missing,
  • every fastboot binary needs to be executed to write a replacement of itself.

Similarly, ADB cannot provide recovery mode support because it relies on the board being booted into userspace and userspace must be configured to allow access.

Problems with bootloader storage

It remains possible for any test job to corrupt any filesystem to which the test job kernel has access. Boards which host the bootloader files on a partition of the primary storage media are particularly vulnerable to bricking through this method. Many U-Boot devices suffer from this problem and LAVA uses TFTP on most of these devices to limit the number of failures.

Problems with full system images

Some boards host the bootloader files on the same storage medium as the kernel and/or operating system and then expect to write a full system image to that storage. The best way to manage such boards is to use a BMC. If that is not available, ensure that the bootloader build used in the system images is never changed until it has been tested and the update has been approved by the lab admins. i.e. treat the bootloader part of the system image build in exactly the same way as a firmware or bootloader update on any other board which lacks bootloader testing and recovery support.

It is not recommended to allow full system images to change more than one component of the image in a single test job.

Important

A primary objective of CI and LAVA is to find breakages in places which developers did not expect to be present, whether those are new bugs or regressions. Every change in every element of the device and the entire software stack needs to be tested in isolation. Only change that one element at a time, keeping all other components identical to other test jobs. Every part of a board and every part of the software stack must be considered as untested and unreliable until proven otherwise.

Not all testing needs to happen in LAVA or even in automation. Not all test operations can be supported in automation.

HiKey 6220

This board provides jumpers which can be bridged and connected to relays to change the boot order when power is applied. Custom software is needed to select recovery mode boot by setting the correct jumpers. Once in recovery mode, the board offers a USB TTY device which can be used to deploy the firmware using custom software from the manufacturer. Once the firmware is transferred, the board comes up in fastboot mode and the rest of the boot files can be transferred over the USB OTG port.

The HiKey 6220 uses a combined deployment of UEFI firmware and a fastboot client which is then executed to deploy the boot and system images.

If the firmware fails, the board can be switched back to recovery mode without needing to interact with the device and a known working build can be deployed instead (using a health check or a second deploy stage of the test job itself). By using the control of the jumpers, the board can be forced into recovery mode without any need to interact with the bootloader.

An example test job for the hikey 6220 using recovery mode includes three deploy actions: recovery, fastboot, and operating system (OpenEmbedded or AOSP). This is to ensure that the firmware is tested in a wide range of modes after being deployed. (Specifically, the test ensures that the firmware continues to allow changes to the partition tables without affecting serial numbers or other device behavior.) This example is used as a health check, deploying a known good build of the firmware, so can be used to recover from a broken build.

Recovery deployment

1
2
3
4
5
6
- deploy:
    timeout:
      minutes: 10
    to: recovery
    namespace: recovery
    connection: lxc

AOSP deployment

1
2
3
4
5
- deploy:
    timeout:
      minutes: 15
    to: fastboot
    namespace: hikey

OpenEmbedded deployment

1
2
3
4
5
6
7
- deploy:
    timeout:
      minutes: 45
    to: fastboot
    # OE deployment
    namespace: hikey
    connection: lxc

Download / view complete hikey complete test job YAML.

Limits of HiKey 6220 recovery

There are limits on how the HiKey 6220 operates in recovery mode:

  1. Requires external hardware (switchable USB hub, relays for the jumpers and custom serial hardware or cables.)

  2. Transfers over a hardware USB TTY device which does not identify itself uniquely to the worker. Only one board can be attached to any one worker.

  3. Fastboot method requires the use of LXC or a custom Docker image

  4. There is no support for a recovery firmware image to be kept on the board alongside the test software. Admins need to identify a known working build which can be used in health checks.

  5. At times, the firmware software itself has not supported a smooth rollback to previous versions. This takes the device offline as soon as a health check tries to deploy the previously known working version. Admins then need to establish a new known working version before bootloader testing can continue.

These limits mean that boards with the necessary jumper support must be isolated from boards without jumper support. Despite the HiKey only supporting UEFI and not U-Boot or another bootloader, the recovery mode cannot be used for all test jobs due to these limits.

Juno

The Juno board provides a BMC which allows LAVA to deploy a new build of bootloader without interacting with the current bootloader. Juno also supports testing two different deployments, U-Boot bootloader and UEFI firmware.

The BMC is accessible before the bootloader is executed, so if the test job determines that the bootloader has failed, a known working build can be deployed to recover the board.

Recovery deployment

1
2
3
4
5
- deploy:
    namespace: recovery
    timeout:
      minutes: 10
    to: vemsd

U-Boot boot action

1
2
3
4
5
- boot:
    namespace: debian
    connection-namespace: recovery
    method: u-boot
    commands: norflash

Download / view complete juno test job YAML.

The Juno can support either U-Boot or UEFI. The BMC on Juno is sufficiently reliable that all test jobs use recovery deployments to ensure that the test job starts with a known bootloader. (Test jobs would otherwise fail when sending U-Boot commands if the previous test job deployed UEFI firmware and vice versa.)

X15 GPEVM

Most of the TI boards provide means to load bootloader using serial interface. This is the case for X15 GPEVM. As compared to other X15 family boards, GPEVM is wired to provide jumpers to switch boot mode. The only HW modification required is populating J5 in order to avoid board powering down before bootloader is loaded to memory and started.

In order to start board in recovery mode, the following HW settings should be set:

  1. Jumpers J3, J4 and J6 should have 1-2 link closed
  2. Jumper J5 should be populated and closed

Example LAVA recovery test job loads ‘known good’ u-boot to memory and follows with flashing the same u-boot to eMMC. This means that host has to have the board connected as USB slave. Example LAVA settings assume that all jumpers are controlled with relay.

Recovery deployment

1
2
3
4
5
6
- deploy:
    timeout:
      minutes: 10
    to: recovery
    namespace: recovery
    connection: lxc

OpenEmbedded deployment

1
2
3
4
5
6
- deploy:
    timeout:
      minutes: 25
    to: fastboot
    namespace: droid
    connection: lxc

Download / view complete x15 complete test job YAML.